Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
Were you interested in related information concerning Tools You Need to Install a New Bathtub ?
Mounting a tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently easily accessible, the project can relocate speedily; if you need to open up a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and embeded in the brand-new one. Make certain you have actually certified yourself for the task and also are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This short article will certainly aid you set up a new bath tub in your bathroom if you have actually already purchased a brand-new tub and do not need to alter the arrangement of your previous water system pipes.
Your devices and also product list ought to consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be rather problematic because of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making sure that the washers are in place in between the faucet and also the sink. Secure the tap in place with the supplier given backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former type must be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wooden boards under its feet, place the tub in the called for placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the tub up until the spirit level reads level.
To set up faucets, fit the bottom of the outermost versatile tap port to the suitable supply pipeline by making a compression join; then do the same for the various other tap.
Switch on the supply of water and check all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill up the tub as well as likewise examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the tub must wait till the tub has actually been used at least once as this will certainly resolve it right into its last setting.
Getting ready for the Setup
Firstly, the sustaining structure supplied with the bath needs to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its last position.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, triggering the water to pass through the wall surface between the bath and the tiling, leading to complications with wetness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water before securing, to permit the movement experienced when the bathtub remains in usage. The sealant can break fairly very early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that page on How to Install a Bathtub when doing a lookup on the internet. In case you enjoyed reading our blog post please make sure you remember to pass it around. Thanks so much for going through it.
Emergency? Call us! Report this page